Products

Trace Oxygen Analyzers
Percent Oxygen Analyzers
Safety Monitors
Carbon Dioxide Analyzers
Custom Systems

Product Selection Guide
Product Application Guide

Industries Served

Our Products are used in a wide variety of industries and applications.
Learn more...

Applications

Find out how our Products can help you. Fill out our Applications Questionnaire.

Technical Support

Please call us with your questions: 800-262-5977 or 401-333-8580

Portable or Fixed

Whether you need a portable battery operated analyzer or temperature controlled explosion proof system for a fixed installation, Alpha Omega Instruments has the solution.
Learn more...

Contact Information

Alpha Omega
Instrument Corp.
30 Martin Street
Cumberland, RI 02864
Toll-Free: 800.262.5977
Phone: 401.333.8580
Fax: 401.333.5550

Contact Us

Applications Questionnaire

Obtaining complete application information will help us better assess your  requirements and allow us to provide our most cost effective recommendations. Based on your knowledge of the application(s), please complete this form.

Would You Rather Fax This Form?You are free to print the form (PDF Document) and manually complete it so that you may fax it to Alpha Omega Instruments at: 401-333-5550

Name:*
Title:
Company:
Phone:*
Fax:
Address 1:
Address 2:
City:
State (USA and Canada):
Postal Code:
Country:
Project Name (If Applicable)
Number of Gas Streams to be measured:
2. What gases are to be measured?
 
Oxygen
Carbon Dioxide
3. Gas Components
Gas Concentrations
Components
[ Sample Stream 1 ]
Background Gases (List gases with their approximate concentrations)
Oyxgen Concentration (Percent or Trace?)
% PPM
Maximum
Minimum
Carbon Dioxide Concentrations (Percent or Trace?)
% PPM
Maximum
Normal
Components
[ Sample Stream 2 ]
Background Gases (List gases with their approximate concentrations)
Oxygen Concentration (Percent or Trace?)
% PPM
Maximum
Minimum
Carbon Dioxide Concentration (Percent or Trace?)
% PPM
Maximum
Normal
Components
[ Sample Stream 3 ]
Background Gases (List gases with their approximate concentrations)
Oxygen Concentration (Percent or Trace?)
% PPM
Maximum
Minimum
Carbon Dioxide Concentration (Percent or Trace?)
% PPM
Maximum
Normal
4. Acid Gases List any acid gases present in the samples including maximum concentrations.
5. Sample Pressure
Minimum
Maximum
Normal
Units of Measurement
6. Sample Discharge
Atmosphere Back To Process (If yes, then procced to question 7)
7. Back To Process
If the sample is to be returned to the process, what is the pressure at the point of return?
Minimum
Maximum
Normal
Is a sample pump required?
Yes No
If so, what will be the length of tubing between the sample source and the pump? (In feet)
9. Sample Temperature
 
Minimum
Maximum
Normal
Units of Measurement
10. Are there liquids present in the sample?
No Yes (If yes, proceed to question 11)
11. What liquids are present?
12. Condensation
Do you anticipate that any of the sample gas contituents may condense if the sample gas is cooled to approximately 77 degrees F (25 degrees C)?
Yes No
(If yes, please explain)
13. Particulates Are there particulates (solids) entrained in the sample?
Yes No
14. Distance What is the distance from the sample pick-off point to the proposed sensor location?
15. Previous Measurement
Has there been an attempt to measure Oxygen or Carbon Dioxide previous to this?
If so, please explain what technique of measurement was used. (Please list any difficultes that were encountered.)
Equipment Configuration
Please check or fill in those items that are required for this application.
Analyzer with sensor mounted on the electronics enclosure
Analyzer with sensor mounted remote from the electronics
 
Distance between sensor and electronics, in feet, if a remote sensor is required:
 
Bench-top Electronics Cabinet
Panel Mounted Enclosure
NEMA 1 (General Purpose Electronics Enclosure)
NEMA 4 (Watertight Electronics Enclosure)
NEMA 7 (Explosion Proof Electronics Enclosure)
 
For all explosion proof requirements (NEMA 7), please indicate:
Class
Group
Division
Electrical Classification
If the sensor is going to be remotely mounted, please indicate the desired electrical classification of both the electronics enclosure and the remote sensor enclosure:
Electronics Enclosure
Remote Sensor Enclosure
Would a blind transmitter be preferred over an analyzer?
What power is available?
Is serial communication desired?
No RS232C RS485
Tagging Required?
If so, please indicate what is to be shown:
Application Description Please provide a brief written description of the application. This is particularly important if the installation will be outdoors. In such cases, please provide as muchinformationon the environmental conditions as possible:
Security Code:
Please enter the text you see in the image